- Wireless N150 Access Point Wn604 User Manual Download
- Access Point Vs Router
- Access Point Hr
If you found this page, you probably have a problem and you need a user manual for the device NETGEAR Netgear WN604 IEEE 802.11n 150 Mbps Wireless Access Point WN604-100NAS. Be sure to check that it is the user manual to exactly the device that you are looking for. In our database NETGEAR Netgear WN604 IEEE 802.11n 150 Mbps Wireless Access Point WN604-100NAS it belongs to the category Network Hardware. A user manualNETGEAR Netgear WN604 IEEE 802.11n 150 Mbps Wireless Access Point WN604-100NAS is taken from the manufacturer, a NETGEAR company - it is an official document, so if you have any doubts as to its contents, please contact the manufacturer of the device NETGEAR Netgear WN604 IEEE 802.11n 150 Mbps Wireless Access Point WN604-100NAS directly. You can view the user manualNETGEAR Netgear WN604 IEEE 802.11n 150 Mbps Wireless Access Point WN604-100NAS directly online or save and store it on your computer.
WN604 IG 26July11.fm Page 1 Tuesday, July 26, 2011 6:00 PM
The Netgear WN604 Wireless Access Point's fast wireless speeds allow you to surf, email, stream music, play on-line games, make Internet phone calls, and more. With a built-in 4 port 10/100 switch for adding extra devices such as PC, printer, or web camera, the Netgear WN604 delivers exceptional connectivity, range and speed. Key Features. Wireless N150 Access Point WN604 Enable the SysLog Server The syslog screen allows you to enable the syslog option if you have a syslog server on your LAN. To enable a syslog server: Select Configuration System Advanced Syslog to view the following screen: Select the Enable Syslog check box if you have a syslog server on your LAN. The model WN604 NETGEAR Wireless N150 Access Point WN604 complies with Part 15 of FCC Rules. Operation is subject to the following two conditions:. This device may not cause harmful interference, and. This device must accept any interference received, including interference that may cause undesired operation.
c. Connect the Ethernet cable from the access point to the PC.
8. Power On/Off.
cable into the access point Ethernet
Wireless N150 Access Point Wn604 User Manual Download
Installation Guide
10. Reset factory defaults.
NETGEAR® Wireless N150 Access Point WN604
2. Configure LAN and wireless access.
the power adapter provided with the access
a. Configure the access point Ethernet port for LAN access. Connect to the
access point by opening your browser and entering http://192.168.0.100 in
Follow these instructions to set up your WN604 access point. You can also click the
documentation links on the Resource CD or the NETGEAR knowledge base at
http://kbserver.netgear.com. Refer to the Resource CD or click the Documentation
link on the user interface to access the Installation Guide for instructions on
A login window displays.
b. When prompted, enter admin for the
password, both in lower case letters.
Tip: Before mounting the access point in a high location, first set up
and test the unit to verify wireless network connectivity.
Access Point WN604 user interface
Package Contents
The NETGEAR® Wireless N150 Access Point WN604 contains the following:
d. Select Wireless Settings under the Setup menu on the left navigation pane
and configure your wireless interface for wireless access.
•
•
•
Ethernet cable
8
10
2 3
5 6
e. Under Security, select WEP/WPA Settings and configure the level of data
Power adapter
1. Power (green/amber): The green power LED should be lit. If the Power LED
is not lit, check the connections and check to see if the power outlet is controlled
by a wall switch that is turned off. If the LED is blinking, a firmware upgrade is in
process. If the LED is amber, the access point is performing a self-test.
See the online help or the online reference manual for full instructions.
Installation Guide
f. In the left navigation pane under Setup, select Basic Settings,and
Access Point Vs Router
2
. WPS (green): The WPS LED blinks green when there is WPS activity
. WLAN (blue): The WLAN LED is on steady when the wireless access point is
running. The LED blinks when there is wireless activity. If the LED is off, the
Note: If you change the default sub net of the LAN IP address, you will be
disconnected from the ProSafe Wireless N150 Access Point WN604 user
interface. To reconnect, reconfigure your computer with a static IP address within
3
1.
a. Unpack the box and verify the contents.
4. LAN (green/amber): A green LAN LED indicates 100 Mbps speed. An amber
LAN LED indicates 10 Mbps speed. Blinking indicates activity.
Tip: Before you deploy your access point, reserve an IP address
(based on the WN604’s MAC address) on the DHCP server. That way,
you can configure the access point with a static IP address that you can
always use to log in to make future configuration changes.
b. Prepare a computer with Internet access and an Ethernet adapter. If this
Access Point Hr
computer is already part of your network, record its TCP/IP configuration
settings. Configure the computer with a static IP address of 192.168.0.210
and subnet mask of 255.255.255.0. See the Reference Manual for more
5. Wireless On/Off: Turns the wireless radio on or off.
6. WPS button: Push to automatically configure settings.
In addition to the user manual NETGEAR Netgear WN604 IEEE 802.11n 150 Mbps Wireless Access Point WN604-100NAS, we also provide a support panel to help you solve your problems with NETGEAR Netgear WN604 IEEE 802.11n 150 Mbps Wireless Access Point WN604-100NAS. If you have any questions, you can ask them in the form below. Other users viewing this website will have the opportunity to help you solve your probem with NETGEAR Netgear WN604 IEEE 802.11n 150 Mbps Wireless Access Point WN604-100NAS. Remember that you can also share the solution. If you solved the problem yourself, please write the solution to the problem with NETGEAR Netgear WN604 IEEE 802.11n 150 Mbps Wireless Access Point WN604-100NAS - you will surely help many users by doing so.